Runs 1.12.x without noticeable issues. Upon loading 1.13.x router boots up, but after a power cycle fails to come up. Cant SSH into it either.
Here are the logs from 1.13.x: https://pastebin.com/5TxUmxst
1.12.x working for comparison: https://pastebin.com/NiXnMgZ1
above has dmesg, logread, df-h
Do get this error upon first loading into a freshly flashed unit. Am flashing without preserving settings.
But error goes away upon switching pages. Also is back when flashing the working 1.12.x as well even though I am flashing without preserving settings. Does not come back on 1.12.x when I do a restore defaults.
Other issues with WD MyNet n750 and Gargoyle is that out of the 4 LEDS on the front only the Power LED is lit up. The Internet connection, Wifi and WPS LEDS are always dark.
gargoyle_1.13.x-ath79-generic-wd_mynet-n750 fails to boot after power cycle
Moderator: Moderators
Re: gargoyle_1.13.x-ath79-generic-wd_mynet-n750 fails to boot after power cycle
The problem will probably be here:
Probably something happened to the mtdblock7 partition (/overlay) and it will have a read-only flag.
To be sure - run the mount command and please paste the listing here.
Code: Select all
Fri Apr 9 06:45:21 2021 kern.warn kernel: [ 118.291209] overlayfs: upper fs does not support tmpfile.
Fri Apr 9 06:45:21 2021 daemon.info mount_root: performing overlay whiteout
Fri Apr 9 06:45:21 2021 daemon.info mount_root: syncronizing overlay
Fri Apr 9 06:45:22 2021 daemon.err mount_root: failed to sync jffs2 overlay
To be sure - run the mount command and please paste the listing here.
Turris Omnia with OpenWrt 21.02 - Tested
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Linksys WRT3200ACM with Gargoyle 1.13.x
TL-WR1043ND v2 with Gargoyle 1.10.0
http://gargoyle.romanhk.cz custom builds by gargoyle users
Re: gargoyle_1.13.x-ath79-generic-wd_mynet-n750 fails to boot after power cycle
Nothing too concerning in the logs.
A few reports of the same behaviour on the same device on the OpenWrt forums however, so maybe some kind of regression.
Needs a serial console to know exactly what has failed.
A few reports of the same behaviour on the same device on the OpenWrt forums however, so maybe some kind of regression.
Needs a serial console to know exactly what has failed.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: gargoyle_1.13.x-ath79-generic-wd_mynet-n750 fails to boot after power cycle
Found a serial cable, here is the ouput, looks like the flashing process is corrupt. After a cold boot checksum fails. You can see me here flashing it then on line 380 power cycling:
PS - summited the ticket on github, probably easier to track bugs there?
https://pastebin.com/fPAtD3TJ
shippet:
PS - summited the ticket on github, probably easier to track bugs there?
https://pastebin.com/fPAtD3TJ
shippet:
Code: Select all
U-Boot 1.1.4 (Jan 11 2012 - 20:59:53)
SVN revision: 48
Target board: WRG-ND13
DRAM:
sri
Wasp 1.1
wasp_ddr_initial_config(255): (32bit) ddr2 init
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 242k for U-Boot at: 83fc0000
Reserving 192k for malloc() at: 83f90000
Reserving 44 Bytes for Board Info at: 83f8ffd4
Reserving 36 Bytes for Global Data at: 83f8ffb0
Reserving 128k for boot params() at: 83f6ffb0
Stack Pointer at: 83f6ff98
Now running in RAM - U-Boot at: 83fc0000
id read 0x100000ff
flash size 16 MB, sector count = 256
Flash: 16 MB
pci_init_board: PCIe PLL not set for 40MHz refclk
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: MAC - HIDDEN FROM LOG!!!!!!!!!
athrs17_reg_init: complete
GIGA: athrs17_link_down all port...
eth0 up
eth0
Hit any key to stop autoboot: 1 0
## Booting image at 9f070000 ...
Verifying Checksum ...
csum:
£ùlƒ$›{40
_¤´º5
afterMD5_we_get_digest:
I=ciû÷õ1˜Íþ§;A
Bad Header Checksum.
GIGA: athrs17_link_up lan port...
ar7240>
Re: gargoyle_1.13.x-ath79-generic-wd_mynet-n750 fails to boot after power cycle
I've replied on Github, lets talk there for now
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.