x86 installation
Moderator: Moderators
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
x86 installation
Hi
I am trying to install Gargoyle in x86 router. I first installed openwrt and then I updated the firmware with Gargoyle. But after updating I am not able to access the router.
Is it the right way to install?
Thanks
Badri M
I am trying to install Gargoyle in x86 router. I first installed openwrt and then I updated the firmware with Gargoyle. But after updating I am not able to access the router.
Is it the right way to install?
Thanks
Badri M
Re: x86 installation
If you did not preserve settings, yes this is fine.
If you preserved settings, no start again.
If you preserved settings, no start again.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
Its a fresh install. But it didnt work. I am using APU Engines D4.
Thanks
Badri M
Thanks
Badri M
Re: x86 installation
So which bit isn't working? Can you plug in a screen and look at the console or do any debugging?
And what image did you install?
And what image did you install?
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
Below are the steps I did for installation and debugging.
1. Installed Openwrt by writing the image into SSD
2. Connected through Tera term to verify Openwrt is properly installed
3. Access Openwrt console in browser and updated the firmware by selecting Gargoyle image.
4. Deselected other options to install a fresh build
5. Once updated, accessed the router throw Tera term
6. After system bootup it was displaying junk characters which is not readable
7. SSH didnt work as well
8. Not able to access through browser as well
Image used is:
Openwrt: openwrt-22.03.0-rc1-x86-64-generic-ext4-combined.img
Gargoyle: gargoyle_1.13.0-x86-64-combined-ext4.img
Thanks
Badri m
1. Installed Openwrt by writing the image into SSD
2. Connected through Tera term to verify Openwrt is properly installed
3. Access Openwrt console in browser and updated the firmware by selecting Gargoyle image.
4. Deselected other options to install a fresh build
5. Once updated, accessed the router throw Tera term
6. After system bootup it was displaying junk characters which is not readable
7. SSH didnt work as well
8. Not able to access through browser as well
Image used is:
Openwrt: openwrt-22.03.0-rc1-x86-64-generic-ext4-combined.img
Gargoyle: gargoyle_1.13.0-x86-64-combined-ext4.img
Thanks
Badri m
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
I guess I have used wrong image files to install. I will try again with matching image files.
Thanks
Badri M
Thanks
Badri M
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
Hi
Its fixed now. I took wrong Openwrt version.
Thanks
Badri M
Its fixed now. I took wrong Openwrt version.
Thanks
Badri M
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
Hi
I have managed to fix the installation issue. But after installation I have only one port available and its only for LAN. How to add other ports and WAN. I tried to edit through SSH but when trying to open the /etc/config/network I am getting permission denied error. How to fix this? I appreciate your help.
Thanks
Badri M
I have managed to fix the installation issue. But after installation I have only one port available and its only for LAN. How to add other ports and WAN. I tried to edit through SSH but when trying to open the /etc/config/network I am getting permission denied error. How to fix this? I appreciate your help.
Thanks
Badri M
-
- Posts: 7
- Joined: Sun Dec 20, 2020 12:02 pm
Re: x86 installation
Hi
I have managed to enable all the ports and wan as well. thanks for the help.
Badri M
I have managed to enable all the ports and wan as well. thanks for the help.
Badri M
Re: x86 installation
Great, what was the issue in the end?
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.