Hello all,
Can someone help me with an image for the GL-MT6000?
https://openwrt.org/toh/hwdata/gl.inet/ ... _gl-mt6000
Support GL-MT6000
Moderator: Moderators
Support GL-MT6000
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
Re: Support GL-MT6000
That device is only supported by Snapshot, so no we can’t do that in Gargoyle (yet).
Once it is part of a release perhaps.
Once it is part of a release perhaps.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Support GL-MT6000
It appears to have been back ported into 23.05 after 23.05.2, so possibly a little closer to being supportable in Gargoyle than if it were only in main snapshots.
Re: Support GL-MT6000
Hello Lantis,
I see that you have compiled firmware for GL-MT6000, what is the installation procedure for gargoyle if you switch from the original firmware or from openwrt to Gargoyle?
https://lantisproject.com/gargoyle_cust ... /mediatek/
I see that you have compiled firmware for GL-MT6000, what is the installation procedure for gargoyle if you switch from the original firmware or from openwrt to Gargoyle?
https://lantisproject.com/gargoyle_cust ... /mediatek/
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
Re: Support GL-MT6000
I installed gargoyle on GL-MT6000, INTERNET 1Gbps, in the speed test on the wire it does not exceed 500Mbps Download and Uploud 890Mbps, Connect Via:PPPOE ipv6 dual stack, that's all Gargoyle is capable of, there are some incompatibilities?
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
Re: Support GL-MT6000
Disable Bandwidth Monitor, I reach up to 890/908 Mbps download and 880/923 upload
/etc/init.d/bwmon_gargoyle stop
/etc/init.d/bwmon_gargoyle disable
/etc/init.d/bwmon_gargoyle stop
/etc/init.d/bwmon_gargoyle disable
wdr3600 rev1.4 OpenWrt
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
wrt1900ACS v.2 OpenWrt/DD-WRT
GL-MT6000 OpenWrt/Gargoyle
Re: Support GL-MT6000
What is gargoyle installation procedure for the router? Should I flash 'factory' or 'sysupgrade'?
I always thought that for upgrading from Gargoyle/OpenWRT I have to use 'sysupgrade'.
If so, why 'factory' is provided as the MT6000 is OpenWRT based?
Thanks.
I always thought that for upgrading from Gargoyle/OpenWRT I have to use 'sysupgrade'.
If so, why 'factory' is provided as the MT6000 is OpenWRT based?
Thanks.
Re: Support GL-MT6000
You can just sysupgrade for that device.
The factory image is available for those that want to get rid of the GLiNet uboot. I personally feel that it should be kept as the benefits outweigh any perceived risks.
The factory image is available for those that want to get rid of the GLiNet uboot. I personally feel that it should be kept as the benefits outweigh any perceived risks.
https://lantisproject.com/downloads/gargoylebuilds for the latest releases
Please be respectful when posting. I do this in my free time on a volunteer basis.
Please be respectful when posting. I do this in my free time on a volunteer basis.
Re: Support GL-MT6000
Thanks.
Flashed sysupgrade, no issues yet. Manually copy settings from old router...
Flashed sysupgrade, no issues yet. Manually copy settings from old router...